LocostUSA.com

Learning how to build Lotus Seven replicas...together!
It is currently November 19, 2017, 6:29 am

All times are UTC - 5 hours [ DST ]




Post new topic Reply to topic  [ 54 posts ]  Go to page Previous  1, 2, 3, 4
Author Message
PostPosted: September 9, 2017, 9:43 am 
Offline

Joined: August 31, 2015, 2:24 pm
Posts: 57
Location: Delaware
another small task done: picked up the uprights from the local hot rod shop after getting some heat to get the tie rod to clear the brake rotor. Guy mentioned the miata uprights were very easy to work with.

Also test fit the front suspension bracket jig and after wrestling with it for a few minutes realized that one of the top alignment holes was off by 8mm maybe I need to start measuring 10x instead of 5x. Should be fixed shortly, waiting on a 14mm drill to enlarge the holes on the brackets to match the subaru bushings I am using.


Attachments:
hot rdded uprights.jpg
hot rdded uprights.jpg [ 786.8 KiB | Viewed 232 times ]
Top
 Profile  
Reply with quote  
PostPosted: November 4, 2017, 10:28 am 
Offline

Joined: August 31, 2015, 2:24 pm
Posts: 57
Location: Delaware
Finally got to bolt something to the frame! I probably had the front brackets mocked up for the better part of month and really just needed to make some of the bracing for the U brackets. Got it all tacking in and just had to bolt some stuff up and check. Only item that will have to be re-looked at is the camber adjuster needs some more clearance as the max camber seems to be about -1deg atm, nothing too bad thought.


Attachments:
front suspension both sides.jpg
front suspension both sides.jpg [ 1.11 MiB | Viewed 138 times ]
front suspension frontal.jpg
front suspension frontal.jpg [ 1.11 MiB | Viewed 138 times ]
front suspension passenger.jpg
front suspension passenger.jpg [ 1.47 MiB | Viewed 138 times ]
front suspension template 2.jpg
front suspension template 2.jpg [ 1.03 MiB | Viewed 138 times ]
front suspension template.jpg
front suspension template.jpg [ 792.89 KiB | Viewed 138 times ]
Top
 Profile  
Reply with quote  
PostPosted: November 16, 2017, 9:02 am 
Offline

Joined: August 31, 2015, 2:24 pm
Posts: 57
Location: Delaware
so I ran into a small issue mocking up the steering rack last night. It's something that should have been noticed a long time ago given how much we've handled the yaris steering rack. the pinion on the yaris rack is forward of the rack.....oops. Now I can drive around a lot of things like flats, power band problems, broken suspension but I don't think I would be able to wrap my head around turning the wheel in the opposite direction of wheel change. back to the drawing board on that one.

maybe someone with a middy could use the rack?


Top
 Profile  
Reply with quote  
PostPosted: November 16, 2017, 3:54 pm 
Offline

Joined: August 31, 2015, 2:24 pm
Posts: 57
Location: Delaware
a little searching around and I think I might have a pretty decent solution. sn95 racks, although powered, have metric threads, 15:1 ratios and only 2.5 turns lock to lock. They also appear to be cheap an available. I also found dhempy's helpful posts about flipping the outer tie rods so that seems like less of a big deal. local yard has a couple sn95 racks for $50 but they are $20 cheaper at the u-pull-it and I'll need to grab that silly rag joint as well.


Last edited by hfmaxi on November 17, 2017, 10:20 am, edited 1 time in total.

Top
 Profile  
Reply with quote  
PostPosted: November 16, 2017, 6:25 pm 
Offline
User avatar

Joined: March 30, 2011, 7:18 am
Posts: 1161
Location: central Arkansas
Lock-to-lock is a function of the steering arm length and the maximumum steering angle.

When comparing racks, you want maximum turns left-to-right, then the actual travel in inches.

Strictly speaking you don't need a lot of road wheel angle for "normal driving", but it sure is handy when parking or making tight right turns.

If your rack turns the wrong way, just move the steering column to the other side and go right hand drive. You're welcome. [grin]


Top
 Profile  
Reply with quote  
PostPosted: November 16, 2017, 11:11 pm 
Offline

Joined: August 31, 2015, 2:24 pm
Posts: 57
Location: Delaware
TRX wrote:

If your rack turns the wrong way, just move the steering column to the other side and go right hand drive. You're welcome. [grin]


I've done RHD before, never could stop turning the wipers on when I was making turns, no issues otherwise. I haven't found a good spec for travel per turn yet.


Top
 Profile  
Reply with quote  
PostPosted: November 17, 2017, 12:21 am 
Offline

Joined: December 30, 2007, 1:21 am
Posts: 531
Location: North Van., BC
I knew that if I waited long enough someone else would make the same boo-boo. :D

From my build log in 2009:

Don't ask me how I did it. At some point I started wondering if I could could modify the steering arms to be front steer. When I figured out how to do that it just didn't dawn on me that the rack wouldn't be suitable. To add to that I had the rubber boots on so when I turned it I didn't see the end of the rack wasn't moving in the right direction. It was only when I installed the tie rod, moved the steering wheel and the tire went the wrong way that stunned disbelief set in.

All ended well, the car's been on the road trouble free for 7 years and it's been worth all the head banging it took to build it.

Ron

_________________
They say a journey of a thousand miles begins with a single step. By the time you finish the car it'll feel like you've done it on your knees.


Top
 Profile  
Reply with quote  
PostPosted: November 17, 2017, 12:53 am 
Offline
User avatar

Joined: December 24, 2007, 5:11 am
Posts: 662
Location: Seattle area
I remember that post. Scared me a little. Had a MR2 rack and was hoping for front steer. Couldn't get it to work. Went with a Miata rack.

_________________
Larry in Seattle


Top
 Profile  
Reply with quote  
PostPosted: November 17, 2017, 10:41 am 
Offline
User avatar

Joined: March 30, 2011, 7:18 am
Posts: 1161
Location: central Arkansas
sevenesqueron wrote:
I knew that if I waited long enough someone else would make the same boo-boo.


I paid a pretty penny for a rack the perfect length for what I wanted. Fortunately I caught the mistake before I built the mounting brackets. But I wound up taking a big loss when I finally managed to get rid of the thing.

It was an expensive lesson... enough that I really did consider going right-hand drive.


Top
 Profile  
Reply with quote  
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 54 posts ]  Go to page Previous  1, 2, 3, 4

All times are UTC - 5 hours [ DST ]


Who is online

Users browsing this forum: Bing [Bot] and 8 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
POWERED_BY