LocostUSA.com http://locostusa.com/forums/ |
|
FS: Locost project Southern California http://locostusa.com/forums/viewtopic.php?f=40&t=19125 |
Page 1 of 1 |
Author: | gottaracenow [ November 4, 2017, 9:15 am ] |
Post subject: | FS: Locost project Southern California |
Time to clear out some space in the garage. My Locost 7 project is up for sale. Based on Caterham 7 SV. Wide body, toyota engine/trans with Miata running gear. have most of the needed parts and a good start. Frame is mounted on a small trailer. Asking $3000 or BO. Let me know if you are interested. (619)3226529 Located in San Diego See photos at url=[https://photos.app.goo.gl/afeZxWR3xGtZpwsi1] List of parts: Engine/Trans: Toyota 3SGE JDM 2 Liter naturally aspirated. Toyota T50 transmission Bellhousing to adapt Toyota T50 Transmission Light weight steel flywheel 6 puck sprung hub clutch disc new pressure plate ARP flywheel bolts Hydraulic throw out bearing (Quartermaster 721100) Ignition module (3SGE HYPERPAK) Coil and ignition wires (ACCEL) T50 Drive shaft Starter Cooling: Custom Aluminum 2 pass radiator Overflow tank (Moroso) Exhaust: Silencer Original exhaust manifold Header kit with collector, mandrel bends Electrical: Headlamp set Caterham stop/brake lamps Backup lamp Dash rocker switches and indicators (Carling) Push button start switch (OMRON) Weather Pack harness connectors’ Fuel system: Jaz fuel tank Fuel level sender Vent Cap with rollover ball Fuel injection pump and sump Hard fuel line kit Fuel AN fittings Pressure gage Fuel pressure regulator Fuel Injection: Two Mega Squirt fuel injection modules Fuel injection harness kit Sensors for injector Intake manifold with throttle body Fuel injectors Fuel injector connectors K&N intake filter Brake and Clutch pedal: Tilton brake/clutch pedal assy Tilton brake cylinder kits with reservoirs (2ea) Brake bias bar and adjuster Clutch master cylinder kit with reservoir Fiberglass (Yellow): Nose (Caterham SV) Front cycle fenders (Caterham SV) Rear wings (Caterham) SS rock guard kit (rock guard, piping, pop rivets (Caterham) Fender welting (piping) (Caterham) Stearing: Momo steering wheel Quick release U-joints Ball joints Woodward Collapsing steering linkage Suspension: Miata based rear and front: Many heim joints and weld fitting Needs completion Heater Blower: Arctic heater/blower Vent assy Frame: Mostly finished: Cowl fabricated Needs: Shocks Front suspension Seats Finishing |
Author: | Bent Wrench [ November 6, 2017, 12:14 pm ] |
Post subject: | Re: FS: Locost project Southern California |
This won't last long! |
Author: | ngpmike [ November 6, 2017, 4:15 pm ] |
Post subject: | Re: FS: Locost project Southern California |
So-Cal is a little broad. Can you narrow it down to a city? I've got friends & family there that might be able to check things out for me. Little easier than driving from MO. |
Author: | Bent Wrench [ November 6, 2017, 5:26 pm ] |
Post subject: | Re: FS: Locost project Southern California |
From the pics and parts list I'm already sold. Im glad it's far enough away to limit my interest. |
Author: | ngpmike [ November 6, 2017, 7:40 pm ] |
Post subject: | Re: FS: Locost project Southern California |
Bent Wrench wrote: Im glad it's far enough away to limit my interest. You're probably right! |
Author: | gottaracenow [ November 6, 2017, 11:46 pm ] |
Post subject: | Re: FS: Locost project Southern California |
Socal is a little broad. I'm in San Diego. |
Author: | ngpmike [ November 7, 2017, 9:20 am ] |
Post subject: | Re: FS: Locost project Southern California |
Thanks! Unfortunately all my people are in LA & San Berdoo Counties. |
Page 1 of 1 | All times are UTC - 5 hours [ DST ] |
Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |