Can't triangulate next to the transmission

Whether it's a "book" chassis or another variant, FEA talk or roll cage advice that you're looking for, this is the place to talk frame construction.

Moderators: a.moore, horizenjob

User avatar
Driven5
Posts: 3274
Joined: April 26, 2008, 6:06 pm
Location: Under the weather. (Seattle)

Re: Can't triangulate next to the transmission

Post by Driven5 »

The Aussie mods did not add triangulation to the tunnel either.
-Justin

"Orville Wright did not have a pilots license." - Gordon MacKenzie
User avatar
tibimakai
Posts: 583
Joined: January 14, 2021, 12:19 pm
Building: 442E
Location: San Dimas, CA

Re: Can't triangulate next to the transmission

Post by tibimakai »

I'm incorporating the Aussie mods.
Thanks
Tibor


'20 Alfa Romeo Stelvio daily
Locost/442E in progress
User avatar
Miatav8,MstrASE,A&P,F
Automotive Encyclopedia
Posts: 8104
Joined: December 22, 2006, 2:05 pm

Re: Can't triangulate next to the transmission

Post by Miatav8,MstrASE,A&P,F »

I see your tunnel design unique so no need to worry about best practice, imho. It's already built. You can skin the outside in steel or aluminum without diagonals. It isn't critical. You can provide a smaller access panel over the skin later if needed.
Miata UBJ: ES-2074R('70s maz pickup)
Ford IFS viewtopic.php?f=5&t=13225&p=134742
Simple Spring select viewtopic.php?f=5&t=11815
LxWxHt
360LA 442E: 134.5x46x15
Lotus7:115x39x7.25
Tiger Avon:114x40x13.3-12.6
Champion/Book:114x42x11
Gibbs/Haynes:122x42x14
VoDou:113x44x14
McSorley 442:122x46x14
Collins 241:127x46x12
User avatar
tibimakai
Posts: 583
Joined: January 14, 2021, 12:19 pm
Building: 442E
Location: San Dimas, CA

Re: Can't triangulate next to the transmission

Post by tibimakai »

Thanks.
I will need to have a service panel, to fill the transmission with oil.
Also, I will have to stick some heat/sound insulation from the inside of the car, otherwise I will damage it, when I remove the trans.
I will cover it with some carpet. I'm hearing that, that area gets very hot, specially here in LA.
Tibor


'20 Alfa Romeo Stelvio daily
Locost/442E in progress
User avatar
RTz
Posts: 608
Joined: July 7, 2011, 12:17 am
Location: Oregon City

Re: Can't triangulate next to the transmission

Post by RTz »

You might find this thesis useful/helpful...

https://www.dropbox.com/s/apear4a8dbahx ... B.doc?dl=0
Peace, Ron
User avatar
tibimakai
Posts: 583
Joined: January 14, 2021, 12:19 pm
Building: 442E
Location: San Dimas, CA

Re: Can't triangulate next to the transmission

Post by tibimakai »

Thanks for that, it is very good document. I will implement quite a few of their suggestions, specially at the front of the car and around the engine/dash area.
Between the engine and the front suspension tubes, I have quite a large open area there.
Tibor


'20 Alfa Romeo Stelvio daily
Locost/442E in progress
FieroReinke
Posts: 555
Joined: January 27, 2010, 1:11 pm
Building: Miata Based 7
Location: Jefferson City, MO

Re: Can't triangulate next to the transmission

Post by FieroReinke »

For reference I did what you are proposing and skined certain areas rather than triangulating them. I would not hesitate. If weight is a great concern go 18ga but if not go 16 ga. Depending on location decide if you feel it needs full weld or just skip weld.
User avatar
tibimakai
Posts: 583
Joined: January 14, 2021, 12:19 pm
Building: 442E
Location: San Dimas, CA

Re: Can't triangulate next to the transmission

Post by tibimakai »

Thanks for that. I will skin that area with 16 ga.
I have asked here, just to be sure, that it's OK to do this.
Tibor


'20 Alfa Romeo Stelvio daily
Locost/442E in progress
Post Reply

Who is online

Users browsing this forum: Semrush [Bot] and 0 guests